(248) 348-7800

sales@belknaptools.com

Printer-Friendly VersionPrinter-friendly version


Printer-Friendly Version

Contact Us

Van F. Belknap Co., Inc.
29164 Wall Street
Wixom, MI 48393 USA
(248) 348-7800
sales@belknaptools.com

Printer-Friendly VersionNEED A SPECIALLY
DESIGNED TOOL?

You're at the right place! Belknap is the Leader in Specialty Torque Applications. Check out our Specialty Tools Gallery for a small sampling of what we've produced for our customers over the years.

MARKING PRESET TORQUE WRENCHES
Ink & Punch

Marking Torque Wrench

BELKNAP’S MARKING PRESET TORQUE WRENCHES are designed for FINAL TORQUE VERIFICATION only, and are not intended to be used for torquing down the fastener. They will leave a positive mark (ink or indentation) for torque verification, so that a simple visual inspection is all that is needed to confirm that torque has been applied. THEY WILL NOT MARK ACCIDENTALLY. All marking torque wrenches are custom made to suit your application.

Click here for a condensed one-page PDF.

Top Side Ink Marking Torque WrenchINK MARKING Preset Torque Wrenches

  • Accuracy is ± 4%.
  • Only marks in CW direction.
  • Manually operated. 
  • Non-coagulating ink, includes two
    ink cartridges. 
  • Available ink colors are Red, Blue,
    Yellow, Green and White. 
  • Felt tip left uncovered after long periods of time may require minimal priming.
  • Approximate ink cartridge cycles is 350-400 and dependent upon the operator/application.
  • Ink is also available by the quart.
  • Cannot mark any type of screws, including Allen or Torx (but may be able to mark an adjacent area.)

Hex Size A.T.F. (across the flats) and Torque Limitations — TOP Ink Style

     • The smallest we can mark is 1/2" or 12mm.
     • Torque Range is 4-135 Ft.Lbs. or 5.4-183 Nm*

Hex Size A.T.F. (across the flats) and Torque Limitations — SIDE Ink Style

     • The smallest we can mark is 9/16" or 14mm.
     • Torque Range is 5-135 Ft.Lbs. or 6.8-183 Nm*

     NOTE: Please check your requirements with us. Torque output capacity will be limited
     by the Socket size or the Opening size of the head.


Punch Marking Torque Wrench

PUNCH MARKING Preset Torque Wrenches

  • Accuracy is ± 4%.
  • Only marks in CW direction.
  • Requires 90 psi standard, non-lubricated
    shop air.
  • Replaceable striking pins will eventually become a bit dull and will need to be
    easily re-sharpened on a belt sander. 
  • Approximate striking pin cycles are application dependent. In our lab tests, we obtained a minimum of
    300 punches before resharpening and 10 resharpenings before replacing.
  • Cannot mark any type of screws (but may be able to mark an adjacent area.)

Hex Size A.T.F. (across the flats) and Torque Limitations — TOP Ink Style

     • The smallest we can mark is 1/2" or 11mm.
     • Torque Range is 4-150 Ft.Lbs. or 5.4-203.4 Nm*

Hex Size A.T.F. (across the flats) and Torque Limitations — SIDE Ink Style

     • The smallest we can mark is 9/16" or 14mm.
     • Torque Range is 4-150 Ft.Lbs. or 5.4-203.4 N*

     NOTE: Please check your requirements with us. Torque output capacity will be limited
     by the Socket size or the Opening size of the head.


    REQUEST A QUOTE
    Each application is unique, therefore, in order for us to quote accurately, we’ll need the following information. Either submit your request online below, or give us a call at (248) 348-7800, and we’ll be happy to discuss your requirements over the phone.

    We must see a photo of your application; you can upload it here:

* Upload a Photo
No file selected
* Target Torque Requirement
* Hex Size of the Fastener to be Torqued
* Marking Type
* Style

(The next two questions refer to this diagram.)
* Application Type
* Application Dimensions


* First Name
* Last Name
* Phone
* Email
* Company Name
Address
City
State
Zip Code

Your Type of Business
 
What is the best way to reach you? Mail
Phone
eMail
 
How did you hear about us? Yellow Pages
Internet Search
Banner Ad
From a Friend
Other
 
Spam Challenge.
This test is to make sure
you're not a spam generator.
What is ?

 

Please feel free to call us for any reason (248) 348-7800. We look forward to speaking with you.

  • Crowfoot Male Square Drive by Female Square Drive
    Crowfoot Adapters
    #1 Male Square Drive
    by Female Square
    Drive Crowfoot
  • Magnetic Inserts Non-Marring Hand Tool
    Material Handling
    #2 Non-Marring Hand Tool
    with Magnetic Inserts
  • Magnet Hand Socket Tool
    Sockets
    #9 Hand Socket
    Tool with Magnet
  • Tool Hand Hose Clamp
    Hose Clamp Tools
    #7 Hand Hose Clamp Tool
  • Fixture Window Button
    Fixtures
    #12 Window Button Fixture
  • Male Hex Drive V-Bottom Extended Adapter
    Drive Ends
    #19 V-Bottom Extended Adapter
    with Male Hex Drive
  • Drive End Adapter Hose Fitting End
    Drive Ends
    #29 Hose Fitting End
    Adapter Drive End
  • Fixture Holding
    Fixtures
    #14 Holding Fixture
  • Handling Hook for Automotive Frame
    Material Handling
    #10 Automotive Frame
    Handling Hook
  • Tips Interchangeable Hose Clamp Tool
    Hose Clamp Tools
    #3 Interchangeable Hose
    Clamp Tool Tips
  • Side Ink Marking Torque Wrench Formax Drive End
    Drive Ends
    #5 Formax Drive End
    for Side Ink Marking
    Torque Wrench
  • Removal Tool Breather Valve
    Assembly & Installation
    #1 Breather Valve
    Removal Tool
  • Pipe Wrench Drive End Torque Wrench
    Torque Wrenches
    #4 Torque Wrench with Pipe
    Wrench Drive End
  • Crowfoot Box Offset Female Square Drive
    Crowfoot Adapters
    #2 Box Offset Female
    Square Drive Crowfoot
  • Square Drive Hex Driver
    Sockets
    #12 Hex Drive with
    Square Drive
© 2003-2017 Van F. BELKNAP Co., Inc. • 29164 Wall Street, Wixom, MI 48393 • CALL 248-348-7800 • FAX 248-348-9821 • EMAIL sales@belknaptools.com